19 Series (59 Products)
TRANBERG® Xenon Searchlight Interface Module Series TEF2650
- DIN rail mounting.
- Built-in snubber network which allows termination of a wide range of communication cable, 100-250 Ohm characteristic impedance. End resistors shall not be used.
- 8 individual potential free relay outputs, single pole NO / NC contacts.
TRANBERG® Relay Output Module for LED Navigation Lights Series TEF4900
- DIN rail mounting.
- 4 or 8 output circuits.
- 2-pole switching. Both poles fused.
- For connection of LED navigation and signal lights. Threshold current value: 34mA.
- Connected LED light must have built in life time control.
- Connected LED light must be selfmonitored and if a failure arise, current must be reduced to <31mA.
- Lamp circuits galvanic isolated from control circuit
- Local emergency switches for control of outputs.
- Connections for main and emergency supply to output circuits.
- Built-in snubber network which allows termination of a wide range of communication cable, 100-250 Ohm characteristic impedance. End resistors shall not be used.
- Current detection can be disabled on any circuit if a particular system does not require this feature.
Integrated Helideck Light Control TEF46003xx
- All control gear in one cabinet, simplifying connections, control and monitoring
- Smaller footprint than individual control cabinets for each type of light
- Combined with Stahl Tranberg’s new line of LED helideck lights means an installation with an absolute minimum of required inspections and minimized maintenance
- Connection with a supervisory control system through Ethernet, Profibus or similar standards
- Pre-programmed touchscreens with an intuitive and user-friendly man-machine interface
- Optional remote button and lamp control panel, allowing additional control of lights
- Optional integration towards HMS (Helideck Monitoring System), allowing direct input from the HLO (Helideck Landing Officer)
- Integration towards SCADA (Supervisory Control And Data Acquisition) systems, allowing remote control from other locations, helicopter pilots, etc.
TRANBERG® Windsock with Internal Illumination and Obstruction Light Series TEF9968
- NORSOK C-004 Compliant
Rugged and solid construction
Easy to install and maintain. Maintenance free lights.
The windsock is internally lit with red light, causing minimal glare and minimal reduction in pilot’s ability to see in the dark
Delivered with 10 meter flying lead armored cable Ø 13 ± 1,5 mm (other lengths on request)
Red + IR (NVG compatible) obstruction lights available
Resistant to vibrations
Bearing for the rotating wind vane is encapsulated in solid brass housing
EN/DIN mounting flange for 60,3 mm pipe
Delivered with one spare windsock kit
TRANBERG® Windsock without Internal Illumination and with Obstruction Light Series TEF9968
- Rugged and solid construction
Easy to install and maintain. Maintenance free lights.
Delivered with 10 meter flying lead armored cable (other lengths on request)
Red + IR (NVG compatible) obstruction light on top available
Resistant to vibrations
Bearing for the rotating wind vane is encapsulated in solid brass housing
Integrated Helideck Light Control TEF4600
- All control gear in one cabinet, simplifying connections, control and monitoring
- Smaller footprint than individual control cabinets for each type of light
- Combined with Tranberg’s new line of LED helideck lights means an installation with an absolute minimum of required inspections and minimized maintenance
- Connection with a supervisory control system through Ethernet, Profibus or similar standards
- Optional touchscreen, allowing local control (Zone 1 panel or non-Ex)
- Optional remote button and lamp control panel, allowing additional control of lights
TRANBERG® ILED Aquarius Circle and H Series TEF 9952
- Great visibility.
- Simple installation.
- Robust design.
- Minimum maintenance requirements.
- Low profile.
- Unique “interlock” design to withstand impact shear forces.
- The light intensity is adjustable - full control by communication.
- Can be fully integrated with TRANBERG® IMT Helideck status light Systems.
- Easy connection, by plug system.
- A variety of fixing methods - to suit all helideck types.
- Easy to replace fixtures.
- Low power consumtion.
- Special anti-slip coating.
- In accordance with the CAP 437 8th edition & ICAO Annex 14.
Commander Utility, Dual Power, Helideck Lights Control System Series TEF4500
- Ready for installation; comes complete with control panel and enclosure with 8 outgoing circuits, B10A.
- Control panel may be mounted far away from the enclosure.
- Up to 7 control panels may be connected to the network, enabling control capabilities from each location.
- Common alarm on circuit breakers
- Naut-OSV alarm signalling towards brigde alarm handling system (BAMS etc.)
- Auto fallover to emergency power source accordingly to DNV Pt. 6 Ch. 1 Sec. 2 F503
TRANBERG® Commander utility interface Series TEF4500
- DIN rail mounting.
- 24 individual potential free outputs, 1 N/O contacts.
- Built-in snubber network which allows termination of a wide range of communication cable, 100-250 Ohm characteristic impedance. End resistors shall not be used.
- Alarm input: 24VDC opto-isolated, 2 pcs.
- Alarm reset input: 24VDC opto-isolated.
TRANBERG® Commander Navigation Light System Central Processing Unit Series TEF4900
- DIN rail mounting.
- Supplies control power to the modules in the commander system.
- Monitoring of up to 4 power supplies, 24VDC.
- Potential free general alarm output, 1C/O contact.
- Alarm silence digital input, 24VDC.
- Alarm mute output, 1C/O potential-free contact. Used to mute the alarm at an external alarm centre.
- Galvanic isolated communication port for alarm handling connection to Voyage Data Recorder (VDR) or SCADA interface.
- Built-in snubber network which allows termination of a wide range of communication cable, 100-250 Ohm characteristic impedance. End resistors shall not be used.
TRANBERG® Fused Flasher Module with Current Detection Series TEF4900
- DIN rail mounting.
- 2-pole switching. Both poles fused.
- Zero-cross switching.
- Build-in current detection to determine if output circuits are OK or not.
- Lamp circuit galvanic isolated from control circuit.
- Connections for main and emergency supply to output circuit.
- Build-in snubber network which allows termination of a wide range of communication cable, 100-250 ohm characteristic impedance. End resistors shall not be used.
- Current detection can be disabled if a particular system does not require this feature. This may be done in software confi guration or as a direct setting on the module.
- The module may also be set locally to manually adjust fl ashing pattern.
TRANBERG® Navigation Light System Relay Output Module Series TEF4900
- DIN rail mounting.
- 8 individual potential free outputs, 1 C/O contacts.
- Built-in snubber network which allows termination of a wide range of communication cable, 100-250 Ohm characteristic impedance. End resistors shall not be used.
